I made my first batch of beer over the weekend. I didn't have quite enough bottled water on hand to add to my wort to make 5 gallons, so I used tap water. I sanitized the hose sprayer on my sink by soaking it in sanitizing solution for 5 minutes, then used it to spray tap water into my primary fermenter until I reached 5 gallons. (I also figured that spraying would help to aerate.) In the future, should I boil the tap water first, or is adding it this way going to turn out ok?


6 Answers 6


There are two issues that need to be addressed before it's safe to use tap water.

First, your water is likely chlorinated. Aside from possibly affecting the yeast, this almost always results in a chlorophenol flavor (think bandaid smell). The chlorine reacts with chemicals in the hops to form the chlorophenol. To fix this, make sure you carbon filter your water to remove the chlorine. This goes for all brewing water, whether adding in your mash, boil, or before fermentation.

The second is sanitation. To be safe, you should probably boil and chill the water. There's likely bacteria that's hard to kill near the opening of your faucet, hose, etc.

  • 2
    AFAIK Boiling water should remove the residual chlorine ehow.com/how_4516999_remove-chlorine-from-water.html Nov 9, 2010 at 23:11
  • 5
    Boiling can remove chlorine, but you have to boil it for a while, 15 minutes at least from what I understand. You can also let it sit for over 24 hours to naturally 'off gas'. However, if the municipality is using chloramine, it can't be effectively boiled off and you'll need to use carbon filtration. You can detect chloramine by placing a large volume of water in a white bucket...it'll kinda have a green tint to it.
    – Morgan
    Nov 9, 2010 at 23:17

Technically tap water should always be sanitized.

Realistically I've never sanitized tap water and never had a problem. Your beer should be fine.

  • Tap water from public sources should be sanitized. However, the much-mentioned chlorophenols can indeed be problematic. Perhaps if your water system uses ground water and thus needs very low levels of chlor*, you can get away with it. Or maybe you don't notice a phenolic touch in the beer. But if your water utility gets high-volume runoff surface water one month, or even fixes a leaking main, they can jack up the sanitizer and definitely cause you some problems. Nov 16, 2010 at 19:31

Safe answer is to boil every bit of water that touches your fermenter. But that's sometimes overkill.

If you have a well like I do, follow the boil rule. Even if the well water checks out clean, they're only looking for coliform, not other things, and even though I have a UV sterilization unit to kill bacteria, there is no residual sanitizing effect in the lines, so there is the chance of clean well water but dirty lines.

If you are on public water, there is almost certainly some type of chlorine or ozone added to kill and then provide residual effects against bacteria. In the USA, they are switching almost everywhere to chloramines, which are far more stable than free chlorine, and thus they can use less of the stuff and have the water stay bacteria free for longer.

Unfortunately, chloramines' stability means you CANNOT remove it by a short boil or by leaving it out overnight. There are two common methods to remove it: Filter through carbon SLOWLY, which will remove the chloramine if done properly, but I have to admit that I wonder if carbon filters themselves can be problematic for sanitation. Adding a reverse osmosis unit after carbon filter is even better. The second method is to simply add sulfites, which react immediately with chloramine and reduce it to zero in a matter of minutes.

I prefer the sulfite method at a rate of about one campden tablet per 10 gallons of water -- you don't need much, just make sure it dissolves and mixes well. There will be some residual sulfite, but the level is so low that it will not affect your yeast, and it will gas off from there early in fermentation. Remember, this is for city water that is already bacteria-free because sulfiting at this weak level will not kill off any bugs that are already in there, and well water doesn't have chloramines anyway.

For city water with chlorine or chloramines, ALWAYS remove those first before brewing with it or adding to a fermenter. I've tasted many otherwise-well-made homebrews that were ruined by using plain chlorinated water. Chlorine plus tannins (from grain or hops) gives you chlorophenols, and these are very, very potent flavor compounds, and not in a good way: medicinal and band-aid.

Calvin Perilloux, Middletown, Maryland, USA

  • +1 for effective use of Campden tablets. I was looking specifically for this treatment and whether it has the effect you described on chloramines. Jul 3, 2013 at 2:30

Because you're adding water before the fermentation starts you're probably fairly safe, especially if you live where you can get city water. If you have a well you might want to test your water, but generally speaking, if you like the taste of your tap water (and you don't get sick drinking it), it should be good enough for your beer.


Here in the UK it's usual for tap water to be chlorinated. This kills bacteria and hence could also kill yeast. I read that leaving tap water to stand for a long period (hours) will make the water safe to use as the chlorine evaporates off.

  • Hmm, I'm pretty sure that I get chlorinated tap water. I didn't even think about killing the yeast. Luckily, the yeast seemed very eager to stay alive, and I had a pretty good bubbling out of the airlock about 12 hours after I pitched.
    – Ben
    Nov 9, 2010 at 20:50
  • I've brewed a handful of beer kits and wine kits using UK mains tap water and had no problems so far.
    – robaker
    Nov 10, 2010 at 14:29
  • the problem isn't that it harms the yeast, the problem is that in encourages chlorophenols (plastic or medicine flavors) to form.
    – baka
    Apr 20, 2011 at 23:28

I wouldn't even add bottled water to my bucket without boiling it first. You may be fine, but you are tempting the beer gods.

  • 1
    Have you had problems, or are you just repeating what you've heard elsewhere? There is substantial paranoia when it comes to sanitation in brewing and it's important to know where to draw the line. Not using bottled water without boiling seems like an extreme.
    – Jarrod
    Nov 9, 2010 at 20:50
  • 3
    The beer gods are a lot more merciful than you might think. Relax, have a homebrew.
    – user122
    Nov 9, 2010 at 21:41
  • 1
    Boiling bottled water seems to be overkill to me.
    – CLJ
    Nov 9, 2010 at 23:44
  • @Zuph, +1 for Papazian Nov 16, 2010 at 19:43

Not the answer you're looking for? Browse other questions tagged or ask your own question.