This is my first time doing any home brewing. I'm using a Mr. Beer kit my parents got me. It has been fermenting for 3 weeks. So I tasted it yesterday and it still has a slightly sweet taste, which I don't mind.

Is it ok to bottle at that point?

3 Answers 3


Hope you're having fun! Did you happen to get a hydrometer reading before fermenting? Three weeks should be enough, but a hydrometer reading can determine it for sure.

  • Lol, no. I know very little about this at this point. This is definitely a kit for the uninitiated. But I can look into one.
    – Patrick
    Feb 6, 2017 at 1:49
  • No worries. Been there before. What style beer is it? Did the fermentation seem active early on?
    – mstrom
    Feb 6, 2017 at 3:30
  • It is a blonde style I believe. A pale at least. I did not monitor it closely early on because the instructions were basically set it and forget it.
    – Patrick
    Feb 6, 2017 at 4:24

Unless the brew has spent three weeks in a very cold place one can usually say that primary fermentation has been completed in that time.

14 days at "room temperature" or slightly below is sufficient for most fermentation to complete. IMHO the beer is ready to be primed and bottled. It will not be ready to drink before 14 days and will need about 7 of those days at room temperature to carbonate correctly. The beer will improve by standing at least a month in the bottles.

Technically speaking, primary fermentation is deemed to have finished when the specific gravity reading is the same for two days in a row. Although I usually allow 3 days - whats the rush!?


Any beer is OK to bottle when the yeast is at the point where it will not over-carbonate the bottles, putting them at risk of pressure-induced bursting.

At what point is this the case?

The generally recommended practice is when three successive gravity readings show the beer stays at the same gravity, and this gravity is roughly at the final gravity you expected. The readings are usually taken over 3 days. Air lock activity is not a reliable indicator of this because CO2 may be escaping through another point (like around a bung or grommet).

Your kit probably included a hydrometer. This measures the density of the liquid it floats in. It looks a bit like a big glass thermometer. Take a sample of beer, and float the hydrometer in it. Read the number that's right at the top of the beer. Your hydrometer might have other units like Brix as well. Here I'm talking about specific gravity, the amount of dissolved sugar in the beer changes how deep it floats (or sinks). As the yeast processes the sugar, the gravity (density) of the beer decreases.

Just to get some numbers into this - for something like a simple pale ale (starting gravity around 1.050) a final gravity of around 1.012 might be OK. If it was still at 1.020 I would be cautious about bottling - especially in glass.

Everything Barking.pete says is generally true in practice (2 weeks fermenting at room temperature is usually enough). But to be sure it's best to take those gravity readings. Temperature can significantly effect the action of the yeast, so if you're room/garage temperature was 14C it would be typical for fermentation to re-start once the beer warmed up. If your not in your target final gravity, it's much easier to fix it in the fermenter than in the bottles!

It's common practice to take an initial gravity reading too. This allows you to determine the alcohol content of the beer by looking at the difference between the starting and finishing gravities.

  • Thank you for the detailed answer. I will learn more as I go. My kit did not include anything fancy like a hydrometer unfortunately. It was a low end kit.
    – Patrick
    Feb 8, 2017 at 2:14
  • @pthumond - perhaps bottle with PET (soft drink) bottles then. Hydrometers are not expensive, and can be purchased online or at every home-brew-supply store.
    – Kingsley
    Feb 9, 2017 at 2:56
  • The kit actually came with plastic soft drink style bottles to bottle into.
    – Patrick
    Jul 3, 2018 at 23:25
  • @pthurmond - that's good, you can squeeze them to see how the carbonation is progressing. If they're still quite soft, they're not carbonated yet.
    – Kingsley
    Jul 5, 2018 at 4:40

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.