1

I am thinking about brewing ginger beer for a bar I work at. This means it would be in a keg on a tap. I would like to ferment the ginger beer instead of pumping in CO2 but am unsure how to go about it. I've done quite a bit of research but the main question I can't find an answer to is how can I safely store my ginger beer in a keg after fermentation has provided enough carbonation without it continuing to ferment?

Being that we haven't done this yet we are not sure how quickly it will move so I would like to avoid any bursting, leakage, or getting too dry.

Is there a way to completely halt fermentation? Not just pause or slow down but entirely stop? I've also read about fermenting ginger beer using the probiotics already present in ginger but not a lot of info on how it may differ in this regard. May this technique provide better results?

Thanks for the help. All suggestions or information is greatly appreciated.

Improve this question
4
  • Potassium sorbate?
    – mellis481
    Oct 24, 2014 at 18:56
  • @im1dermike I will definitely look into that, thanks.
    – user8365
    Oct 24, 2014 at 19:00
  • You'll need to clarify: Are you looking to make a beer, with ginger, or a ginger-beer (the soda; the type you'd put in a dark and stormy?). The answer below seems to assume a regular beer with a primary/secondary fermentation. But your question implies you don't want to produce an alcoholic beverage.
    – Chris Pfohl
    Oct 28, 2014 at 17:15
  • I'm making ginger-beer the soda but it will be slightly alcoholic since i am fermenting it.
    – user8365
    Oct 28, 2014 at 23:29

2 Answers 2

Reset to default
4

If primary fermentation is complete, adding priming sugar only allows the wort to consume the newly added sugar; it doesn't continue to ferment afterward.

In a 5gal corny keg, 4 oz of corn sugar will be sufficient. You must leave it at room temp (just like a bottle) for a couple of weeks. It should carbonate just fine. (Akin to cask conditioning). You can then add CO2 to maintain carb (like a serving pressure of 5 - 10psi). Unless you add some huge amount of sugar, the keg will be fine (they can handle more psi than a bottle). Ideally, if you carbonate at your house, then move it to the bar, let it sit for a couple of days, but that's primarily since the move will kick up trub from keg-carbing. It's a bit easier to control a force carb, but carbing with priming sugar works just fine in a keg, though you typically need a little less (4oz instead of 5oz for a 5 gallon batch, should scale).

If you trying to stop a fermentation early, where it would normally continue to ferment if left alone, then cooling it or using potassium sulfite combined with potassium sorbate accomplishes this, but with postassium sulfite/metabisulfite alone, if returned to room temp, the yeast could overcome it and start to ferment. However, just cooling it will halt most yeasts.

Improve this answer
2
  • Mead and wine "brewers" usually use chemicals to stop fermentation/kill yeast. Not sure what they use, but it is a good place to start.
    – Atron Seige
    Oct 26, 2014 at 16:20
  • 1
    @Atron Mazers and vintners use potassium sorbate and potassium metabisulfite to halt fermentation. Usage and dosage information is widely available online.
    – rjbergen
    Oct 27, 2014 at 15:15
1

Rough filtration followed by sterile filtration, add back sugar, then force carb. This wouldn't be cheap or easy (or even practical at your volume). I would suggest you just purchase a ginger beer for something like this.

Improve this answer

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.