The various hardware items for producing beer or wine. Includes buckets, carboys, kegs, hoses, airlocks, etc.

learn more… | top users | synonyms

2
votes
1answer
161 views

What supplies to bring to a beer festival?

At the risk of being flagged off-topic, as this is a bit tangential to actual brewing and fermentation... It's Spring, and the beer festival season isn't exactly in "full-swing" yet, but I don't know ...
2
votes
1answer
264 views

How big do the holes need to be in a Zapap style Mash/Lauter Tun?

I'm looking to make one of the mash tuns out of a plastic bucket. I find instructions like "drill a bazillion holes into the bottom with a small drill bit". How small? Is there a size that's too ...
2
votes
1answer
686 views

Which size auto siphon to empty a 5 or 6.5 gallon carboy?

I got an auto siphon as a gift recently. Unfortunately, it only reaches about half-way down into the carboy. All the brew supply sites and the fermtech site, itself, aren't exactly clear about the ...
2
votes
1answer
214 views

Bottle drying after sanitisation?

When sanitising and using a bottle tree, should I wait for bottles to dry completely or can I use them just rinsed? The Youngs sanitiser I'm using says items should be used within 1 hour of being ...
2
votes
3answers
1k views

Can a Johnson A419 control both a heater and cooler, or is a single-mode?

I just recieved a Johnson A419 digital temperature controller, but I think I was mistaken in my expectations. I was under the impression I could plug both a heater and cooler into the controller; ...
2
votes
1answer
256 views

Kegging at basement temperature

I am a novice at kegging. I don't have room for a kegerator or chest freezer so I simply keg at basement temperature. My basement is currently 69 F and I've had 5 gallons of tripel on pressure for 3 ...
2
votes
1answer
5k views

Carboy dimensions

What are the dimensions of a 5.5 and 6 gallon standard glass carboy?
2
votes
2answers
583 views

Checking for CO2 leaks

If you have an at home draft system, how do you check for leaks in the CO2 side of the set up? How often do you need to check for leaks?
1
vote
1answer
71 views

Capper indents bottle cap. Is this ok?

I have a standard, hand held bottle capper and when I am using it I am getting indentations in the cap. The larger problem is that I am having issues with inconsistent carbonation and want to ...
1
vote
2answers
93 views

Turn Bottling Bin into a Mash Tun?

If I attach a removable mesh filter to hold back the grains and I properly insulate the entire bottling bin, can I dual wield it as a bottler and as a mashing tun? What benefits are there to having ...
1
vote
3answers
223 views

How to make more beer than I can boil?

I will soon need to buy some more equipment, but I want to think it a little bit what I really need to buy and in the meantime I will try some workaround. I was thinking of brewing mash/extract ...
1
vote
3answers
950 views

Is my copper wort chiller still good?

I haven't had the chance to brew in about two years and I've been storing my copper wort chiller in a storage locker for most of that time. Upon moving and retrieving it yesterday, it's got some ...
1
vote
2answers
3k views

Where are MillerCoors Light Home Draft units available?

MillerCoors used to sell Coors Light Home Draft and Miller Light Home Draft "kegs" at my local grocery store, but I have not seem them in a long time. The reason I ask is because these units are ...
1
vote
1answer
84 views

HERMS waterproof hole in heat exchanger

I'm in the initial phase of my HERMS project, and I'm struggling to come up with an elegant solution to waterproofing the hole where my copper pipe will enter the hot liquor tank. Ideally I'd like ...
1
vote
2answers
128 views

Food Grade Steel Drums

I'm thinking about buying some a HUGE Blue food grade steel drums, which is either painted or enameled.If I correctly modify them, will these be okay for FV, Mashing Tubs, Boil Kettle, Strike Boiler? ...
1
vote
1answer
127 views

Clean kegged, put back together wrong

I recently brewed my second batch of 2x 5 gallon beers. The first time, kegs were recently reconditioned and so I did a quick clean and filled them up. This time, being some time later, I went ahead ...
1
vote
1answer
308 views

Recommendations for scaling up operations

Right now I brew once month. This gets me to 60-72 gallons of delicious wine or beer per year. But the limit for home brewers in the US is 200 gallons per year per household. To reach that with 5 ...
1
vote
1answer
24 views

Push fit auto close valve connector required

This is a question about gear more than brewing, per se... I'm wondering if a particular component exists... I'm trying to find a connector suitable for my system that will allow me to disconnect my ...
1
vote
1answer
5k views

What is a grant?

How is it used? What does it do?
1
vote
1answer
70 views

Starting out with fruit wine?

I have never brewed, but I am playing with the thought of starting to make fruit wines. While I can get very good alcohol of other categories, fruit wines are rare, and some types are not sold here at ...
1
vote
2answers
116 views

Boil kettle from plastic fermentation bin

Can a plastic fermentation bin be modified with a heater element to make a strike-water heater or a boil-kettle?
1
vote
1answer
646 views

What Beer Line or Hose Size Fits the Cornelius/Corny Keg Barbed Quick Disconnects?

I'm needing hoses to run to and from my barbed ball-lock quick disconnect on my cornelius keg. Which diameter should I be getting? Do I need reinforced hoses? Answer: 1/4" (6mm) Inner ...
1
vote
1answer
175 views

Johnson A419 BLE/WiFi Modification

I'm a software engineer who just bought a Johnson A419. I have a Nest thermostat. Naturally, if I can control and monitor my house temps with my iDevices, why not my fermentation? I'd like to hack ...
1
vote
1answer
66 views

Is tin safe on the mash?

A friend is building a manifold and the copper connections he bought have a bit of tin (Sn) on it, supposedly to make the solder easier. He is not going to solder them so the tin will remain in ...
1
vote
1answer
261 views

Looking for a specific fitting

I bought a blichmann therminator, and I want to hook up stainless camlock/ groove 1/2" nipples to all 4 "openings". Problem is, the coolant line in/ out are 3/4" GHT, which, while I understand why ...
1
vote
2answers
125 views

Malt mill gap adjustment

The nature of my work is such that i have all the materials and tools to make a mill so i am not intrested on buying one.I want to know if there is a standard gap between the rollers for all type of ...
0
votes
3answers
130 views

Should I buy two buckets?

There is a sale on homebrew equipment at the moment, and I am adding things to my basket to mimic a starter kit. One thing that I notice is that the kits come with a single fermentation bucket. ...
0
votes
2answers
168 views

What are the differences between mashing and steeping grains in preparation

What is the difference between mashing and steeping grains in terms of preparation style or is "mashing" and "steeping" just word semantics?
0
votes
3answers
70 views

It is necessary to sanitize my wine thief after primary fermentation

I have made several batches of wine from kits and a few batches of mead. One of the things that must be done after primary fermentation is to test the specific gravity. The wine kits I have used ...
0
votes
1answer
86 views

Control Products 9102D Temperature Controller won't go below 50 degrees?

So I got a dual stage controller (http://www.amazon.com/gp/product/B0057APR3I/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1) to hook up to a keezer that I am making. I got it wired up today and was ...
0
votes
2answers
59 views

Monster Mill v.s. Kitchen Aid Mill attachment

We've been looking into getting a grain mill for some time now. I was pretty settled on getting a monster mill or some version of it until I saw the kitchen aid milling attachment. If this would work ...
0
votes
1answer
82 views

What materials are good for mashing/boiling container

What material are good for mashing/boiling. I think stainless steel and copper are good, what about aluminum and enamel?
0
votes
1answer
503 views

Basic equipment needed for all grain brewing [duplicate]

Possible Duplicate: What is the minimum amount of equipment to dabble in All-Grain? I'm considering working on my first all-grain brew batch. What are the bare essentials of equipment to do ...
0
votes
0answers
132 views

Must-have supplies for making one's own beer? [duplicate]

Possible Duplicate: What equipment do I need to buy to start homebrewing? What are the must-have supplies for brewing your own beer? In addition to ingredients, what types of containers, ...