The tag has no wiki summary.

learn more… | top users | synonyms

2
votes
1answer
28 views

Mash Boiler – What's a good boiler?

i'm new to the brewing game and am currently waiting for a few whole grain brews to come of age. One thing i'd like to do is purchase a larger mash boiler and dedicate a bit of space in the shed for ...
2
votes
3answers
128 views

Poor hop aroma for late addition hops

My boil kettle is about 56x85cm, so relatively tall and narrow. I get a good rolling boil but no matter how much hops I throw in in the last 5 minutes I can never seem to get any aroma whatsoever. I'm ...
1
vote
2answers
58 views

Boil options with a small pot

I'm about to make my first brew (from a kit), it's a 25litre batch (6.5us gal). Following John Palmer's advice I will be doing a partial boil. But the biggest pot I have available is 6litres (8qt). ...
1
vote
1answer
81 views

Can I make a 10g batch with a 16g kettle?

I'm planning an upgrade to my 5 gallon setup to do 10 gallon batches. In BeerSmith, I've created an equipment profile to estimate my pre-boil volume. Assuming 1 gallon evaporation per hour (I know ...
1
vote
1answer
119 views

Frying a Turkey in a Brew Kettle

Family wants me to fry a turkey in my 14 gallon brew kettle. I'm all for fried turkey but worried about lasting effects on my kettle. Anyone have experience with something like this? Also open to ...
3
votes
2answers
362 views

Do I need a ball valve on my brew kettle?

I am shopping for a brew kettle so I can upgrade to full volume boils. Many pots have ball valves. I can think of two reasons to use a ball valve Drain through it to avoid picking up the kettle to ...
0
votes
2answers
29 views

Is a 12quart pot sufficient for a 1/2 5gal boil?

I am just getting ready to do my first batch. I have all I need except a descent pot. I found a 12quart used stainless pot on Kijiji and was hoping it would be sufficient for half-boils of 5gal ...
3
votes
1answer
164 views

May be time for new kettle. Advantages of Stainless Steel?

I've had the same 10G aluminum BK since I started AG brewing, about 4 years and 70 batches. I recently left my copper IC in it for a few months and think I may have corroded the aluminum, so it may ...
2
votes
1answer
544 views

Permanent marking of volume in aluminium pot

This technique http://imgur.com/a/dCvS5, shows how is easy to do permanent markings in stainless pot. But what about aluminium ? Does anyone know if it is possible (and safe) to use it in aluninium ...
1
vote
2answers
190 views

Boil kettle from plastic fermentation bin

Can a plastic fermentation bin be modified with a heater element to make a strike-water heater or a boil-kettle?
1
vote
2answers
211 views

Food Grade Steel Drums

I'm thinking about buying some a HUGE Blue food grade steel drums, which is either painted or enameled.If I correctly modify them, will these be okay for FV, Mashing Tubs, Boil Kettle, Strike Boiler? ...
1
vote
1answer
121 views

Are exposed threads in a boil kettle a problem?

I'm currently putting together a new boil kettle, and am planning to use 1/2" NPT threaded fittings attached to a welded coupler. I've seen a lot of designs which have exposed threads and teflon tape ...
0
votes
1answer
530 views

power is cutting out on my (electric) boiler

I have an electrim mashing bin (the standard one of these) that I use as a boiler. This morning as I went to heat my liquor, the element started to cut out (water was around 60°C). When I left the ...
1
vote
2answers
230 views

How can I mount a water heater element to a GoldenGate keg?

I have what I think is a GoldenGate style keg. It's got a bunghole, a tapped hole on top and another near the base. I want to mount a electric hot water heater element in the base hole. The base ...
1
vote
1answer
1k views

Screw dimensions for camco/reliance water heater element?

I'm planning to install a water heater element in my boiling kettle. I have been looking at the Reliance and Camco elements but since neither is easy to get by in Finland I really need to go for a ...
2
votes
2answers
660 views

Stainless Steel Scrubber in Boil Screen to strain hops?

So I have a 6" boil screen in my kettle attached to my ball valve. Now this doesn't strain that much hops out because of the larger holes in the screen so when I transfer it to my carboy I run it ...
5
votes
1answer
699 views

Electric brewing in UK or Ireland

I currently brew beer in my kitchen, but the mess, smells and dirty looks from my wife have taken some of the joy out of my brew day. I started looking into an electric brewing solution that would ...
10
votes
4answers
1k views

Process for transfereing from boil kettle to fermenter

At the moment the most frustrating part of my brewday is getting the cold wort into the fermenter. Here is my process. I have a 20 litre saucepan that i use as a kettle that does not have a tap. At ...
3
votes
2answers
351 views

Is it safe to use a chipped aluminum stock pot?

My 32 qt. aluminum stock pot was just delivered that I was planning to use this weekend. Taking it out of the box and inspecting it, there is a fairly sizable chip on the inside about 3/4 of the way ...
3
votes
2answers
5k views

What wattage element is needed for hot liquor tank/heat exchanger, and what about brew kettle?

I'm completely captivated by www.theelectricbrewery.com, love their directions, and have ordered the parts, so I'll have my experience soon, but what is your experience with selecting hot water heater ...