Take the 2-minute tour ×
Homebrewing Stack Exchange is a question and answer site for dedicated home brewers and serious enthusiasts. It's 100% free, no registration required.

I found a recipe that I would like to try, but it is for a 5 gallon batch and I want to make a 10 gallon batch. Is there anything special that I need to keep in mind or calculate when doubling a recipe or is it a straight up x2 conversion?

share|improve this question
3  
Its going to take twice as long to drink it, I suppose. –  brewchez Nov 23 '10 at 13:11

2 Answers 2

up vote 3 down vote accepted

I mostly agree with chrislarson, but I would propose a few differences, if you wanted to be more precise.

Mash:
2X
Double the amounts of grain and water. Ensure that your mash tun is also wider, so that your grain bed isn't too tall.

Boil:
2X
Since you doubled the volume of hot liquor for the mash, you should end up with twice the volume going into the boil. Also, if you follow the rule of keeping your heat such that you lose 10% wort volume per hour, then your volume should exactly double.

Hops:
2X
There are several formulas to estimate hop utilization, but generally they are a product of the hop weight, alpha acid percentage, and wort gravity. IBUs, volume, and hop utilization are directly related, so if you expect your gravity to be the same as the original recipe, and your volume doubles, then your hop quantities should double as well.

Yeast:
2X
...but this one is tricky, since most homebrewers (and a lot of microbreweries!) don't calculate yeast pitch rates, but instead just toss one vial/pack of yeast into the wort. If you want to be precise, a good guideline is: cells to pitch = (1 million) * (mL of wort) * (°P of the wort)

If you thought your equipment setup was going to result in a higher evaporation rate in the boil, like chrislarson, then you would need more water (either in the mash or added later) and consequently, less hops.

share|improve this answer
1  
Yup, IBU = (Weight * Utilization * AA * 7489)/(Final Volume * Gravity Correction) Since the only two things here that change are the Final Volume in the denominator, which doubles, and the weight, you must double the weight to produce the same IBU. For aroma/flavor there aren't really qualitative methods without chromatography, so you may as well just also double all hops, then iterate a given recipe to taste. EDIT: the constant of 7489 is for English units. –  Mike S Nov 23 '10 at 5:14
    
If one is extract brewing, is it necessary to double the steeping grains as well? –  Andy Baird Sep 27 '12 at 18:27

Mash: Just double the amounts of grain and water.

Boil: You'll need 250% of the water to account for more evaporation (In my experience).

Hops: Judging by what BeerSmith tells me when I scale a recipe, you'll need about 175% of the hops by weight. For both bittering and aromatic.

Yeast: A 16 oz (.5L) starter has always been enough for me. Even with high gravity beers.

share|improve this answer
    
So for hops, if the recipe calls for 1 oz, I will need 175% of that, so 1.75 oz? Just want to clarify. –  Joe Lencioni Nov 23 '10 at 3:48
1  
Yes, sir. When you have a higher gravity in the wort, the hop alpha acids won't isomerize as well. So with 250% of the initial water volume in the boil, you'll have a lower initial sugar concentration; allowing for greater isomerization. That's the chemistry as I remember it. –  chrislarson Nov 23 '10 at 3:58

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.